Speedzilla Motorcycle Message Forums

Speedzilla Motorcycle Message Forums (https://www.speedzilla.com/forums/)
-   V4 motorbikes (https://www.speedzilla.com/forums/v4-motorbikes/)
-   -   My RC30 build (https://www.speedzilla.com/forums/v4-motorbikes/67774-my-rc30-build.html)

mrgrn 12-25-2011 11:46 AM

My RC30 build
Figured i would start things off with some of my build now that we have a place to put these without upsetting the natives:)

Not sure i have enough room here to post many of the pics so maybe i will leave them off for now unless there is a demand for them.

Bike has taken many changes and i have two and three of alot of parts so if you see them double listed this is why

Customized Gilles triples RC51 fork conversion
Carbonpartz Billet clip-ons with carbon tubes
Carbonpartz Billet clutch slave cylinder
K- factory Billet clutch slave cylinder
Carbonpartz Billet rear race rotor
330mm oversize Wave rotors front
custom one off rear carrozzeria wheel
RC51 carrozzeria front wheel
Carbonpartz custom carbon front endurance fender
Carbonpartz carbon rear hugger
Carbonpartz carbon frame guards
Carbonpartz carbon swingarm cover
Sato rearsets
HRC rearset
Carbon fiber rearsets
Carbonpartz Billet rear master cylinder
ISR Billet rear master cylinder
ISR monobloc front radial calipers
Ohlins 50mm forks with radial mount adapters
ISR Billet front bake and clutch master cylinders
ISR mini rear caliper
Carbonpartz custom 4 pot race Billet caliper
Carbonpartz custom Billet rear race caliper hanger
Thorsten Billet rear race brake hanger
Carbonpartz custom Billet drive pins
Custom rear wheel shim spacer
Thorsten carbon fiber bodywork
Thorsten carbon fairing nose support
Thorsten carbon air box
Thorsten carbon ram air tubes
Thorsten carbon sub frame with built in breather
Thorsten cast HRC type clutch side cover with sight glass
HRC deep magnesium sump
HRC pistons
Moriwaki cams and short port suzuka race heads
Berylium valve seats
Kibblewhite Titanium valves
Keihin flatslide carbs with custom Billet vel stacks or CP custom carbon fiber stacks
Ohlins side mount steering damper
penske shock with titanium spring
Moriwaki Billet RC51 suspension link
HRC ride height adjuster
Moriwaki ride height adjuster
stainless brake lines
Thorsten electrical water pump
HRC rads
custom oil cooler
speedcel battery
Carbonpartz carbon thumb brake
Carbonpartz custom ti kickstand
LED gear indicator
Vapor digital dash
Blue printed motor
HRC CDI (yet to find)]
Full LBH titanium exhaust with Black Dragon custom mufflers
Custom first made Samco rad hose kit
Custom Billet rear wheel axle nut
Custom delrin rear wheel axle nut crash protector
Ohlins fork crash protectors
Frame sliders
tons of ti bolts
COMING: custom swingarm
lots more have to look

mrgrn 12-25-2011 12:29 PM

1 Attachment(s)
have a seat

beryllium with ti kibblewhites

mrgrn 12-25-2011 12:39 PM

1 Attachment(s)
hope it brakes OK

mrgrn 12-25-2011 12:45 PM

some older before build pics

sburns2421 12-25-2011 01:19 PM

A nice first thread for the new sub-forum.

Gog 12-25-2011 02:23 PM

Nice Mark. Do you have a youtube vid of that RC3o running?

mikstr 12-25-2011 03:44 PM

Looking good! Can't wait to see a finished pic.

mrgrn 12-25-2011 05:55 PM


Originally Posted by mikstr (Post 692937)
Looking good! Can't wait to see a finished pic.

mee too:(

been a while for sure

mrgrn 12-25-2011 06:03 PM

couple more

mrgrn 12-25-2011 06:05 PM

working on a new Y pipe now for a ultra high mount mini GP can 79mm diameter carbon can or a tri oval twin baffle.

Ben710 12-25-2011 08:09 PM

Fully sick, thanks for sharing.
Please post more!

mrgrn 12-26-2011 12:51 AM


Originally Posted by Gog (Post 692932)
Nice Mark. Do you have a youtube vid of that RC3o running?

somewhere i think i might, let me take a look. i can tell you with my GP can on there it is a simply nasty sounding beast

mrgrn 12-26-2011 12:54 AM


Originally Posted by Ben710 (Post 692963)
Fully sick, thanks for sharing.
Please post more!

Thank you

I will post pics up when i get the bike done of my custom carbon fiber gas tank too :D The bodywork is getting painted silver here as we speak i hope.

I am planning on having a custom swingarm made that allows for better tire width clearance and is 10mm longer like the HRC unit from either billet block wittled down or maybe a greggs custom boxed in and coated, not sure yet. I am leaning towards a GC though TBH and i am hoping it will be not too heavy though

ericf1 12-27-2011 07:20 PM

Great looking bike, cant' wait for more pics.

MC Leather 12-28-2011 09:38 PM

I saw it a Jim's a few months ago. I'm sure the finished project will be unique.

CORNER_MONSTER 12-29-2011 05:40 PM

looks like a lot of hard work, very nice even though it is not my cup of tea.

sqd8r 01-08-2012 12:00 AM

Nice stuff Mark, looking forward to more updates. Thx. :)

vfrrider 01-18-2012 03:43 AM

Officially hooked.


mrgrn 01-18-2012 09:58 PM

currently getting painted

hope to have some pics soon

mrgrn 06-26-2012 10:21 PM

Heavy flake silver is now applied:D

Some black and possibly purple going down today or tomorrow and it will be almost done:)

I still have a bunch of other one off goodies and the swingarm to have made but it basically will be done-ish:p enough to drive finally.

I have ordered some ti tubing so i can make a new Y pipe to make the muffler a high mount instead of a low mount.

I have thought about having Gregg make a tube style swingarm and doing some box in but i am not sold on the look and weight. I am now able to machine parts and have taken my 5 year old idea of a billet arm and reinvented it, what do we think of a billet arm?

All times are GMT. The time now is 10:14 AM.

Powered by vBulletin® Copyright ©2000 - 2019, vBulletin Solutions, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
© 2011, Speedzilla.com, Inc

For the best viewing experience please update your browser to Google Chrome