Pic of my LIGHTENED, BALANCED, and POLISHED 999 Crankshaft.

Looks good!

Who did the work?

Jason has the hookup.

Whaa?!?! No knife-edging?

Seriously though. that's a nice looking crank.

What will be the performance benefit (that is a serious question as well)?

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Holeshot &raquo;</TD></TR><TR><TD CLASS="quote">Whaa?!?! No knife-edging?

Seriously though. that's a nice looking crank.

What will be the performance benefit (that is a serious question as well)? </TD></TR></TABLE>

Motor should spin up quicker, slightly better handling due to reduced gyroscopics, increased engine life.

That should just about do it.

very pretty

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Turbo329 &raquo;</TD></TR><TR><TD CLASS="quote">

Motor should spin up quicker, slightly better handling due to reduced gyroscopics, increased engine life.

That should just about do it.</TD></TR></TABLE>

you need to slow it down or you are either going to
1:run out of projects
2: run out of $$

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by phil77 &raquo;</TD></TR><TR><TD CLASS="quote">

you need to slow it down or you are either going to
1:run out of projects
2: run out of $$

</TD></TR></TABLE>

I got the fever. Hey, you only live once right?

Nice Shaft.

roughly how much did that run ya if you don't mind?

how much lighter is it?

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Turbo329 &raquo;</TD></TR><TR><TD CLASS="quote">I got the fever. Hey, you only live once right? </TD></TR></TABLE>


Damn straight...

I try to jam it all in now. I might not be here tomorrow.

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by spawn_x &raquo;</TD></TR><TR><TD CLASS="quote">roughly how much did that run ya if you don't mind?

how much lighter is it?</TD></TR></TABLE>

$700

4 lbs

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by section8superbike &raquo;</TD></TR><TR><TD CLASS="quote">

$700

4 lbs</TD></TR></TABLE>

Stop giving away my secrets!!!!

Lets see....7lbs per hp.....$700 for 4lbs....hmmmmmmm

H8

4lbs off of rotating mass does more for flickability than 25lbs elsewhere on the bike.

Do your homework champ!!!

Wasn't a heckle...trust me...I was figuring out my budget!

H8

See what you started Jason!!!!!!!!!!!!

I have one that is a lot like that for a pre-1999 748-853 that I can nolonger use if anyone is interested. The cost per pound would be considerably better :-)

Jason probally sends them to http://www.foxperformanceengines.com Ben charges much less than $700, Bens price $499

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by MKIA &raquo;</TD></TR><TR><TD CLASS="quote">Jason probally sends them to http://www.foxperformanceengines.com Ben charges much less than $700, Bens price $499</TD></TR></TABLE>

Nope, Jason doesn't send it to FOX.

Isn't Fox in Australia????