998r/996 parts for sale

stevet · #1 (**permalink**) 09-29-2008, 10:10 PM

New 998r bodywork from #469 2002 998r complete never mounted $3500
50mm Termi Complete exhaust from 998r used but nice $1500
Parting out 996 track bike: Showa front end with racetech springs set up by gmd for 195lb rider $350. Complete front brake calipers, stainless lines and rotors $350. 2 rear rotors as new $50ea. new rear brake caliper with rear master and lines $250. Alum subframe, bent once but straightened and on bike now $350. 51mm carbon exhaust by ferraci, as new, with headers and hangers $900. stock 996 exhaust with headers and carbon slipons, used but great shape, $350. rear swingarm as new with bearings, eccentric and carbon guard, $350. ohlins rear shock ridden twice since serviced by cogent dynamics with spring, $375. Corsa heads 0 hours since new ex valves, setup and dyno by mellilimoto,bolt and and go $1500. Stock 996 heads with sps cams and new bdc rockers from bcm with less than 200 miles on them bolt on and go $1200 (cams and rockers cost 1450), bcm 1036 jugs and pistons with less than 1000 miles $800, 50mm 996 throttle bodies $175. race wiring harness by bruce at bcm with kill switch for 1.6ecu $200. 19/18 radial front brake master with res and line $250. Corsa large oil cooler for 996, as new $450. Custom used carbon airbox by bcm fits throttle bodies in airbox with removable side covers race part only, $350. Underseat oil catch can in carbon, epoxy at seams to prevent leaks $375. Complete Sebimoto bodywork with custom yellow, green and white stripe paint includes tail and ama lower and bellypan (small repair left side) $750. Yellow perfect tank with pump $575. yellow carbon/kevlar oversize intakes$150, stock 996 radiator good shape $150. yoyodyne clutch slave in gold as new (1 year old) $175. 996 heads with 2mm over valves with stock cams $350. stock 996 pistons and rods <1000 miles $150. fast by ferraci hi comp 12.2 pistons $250. 2 sets snowflake 996 rotors $150. ea. All internal gears, side covers, etc and coils, wires off 2001 996, call with needs. thanks steve, tnt racing

dcarlock · #2 (**permalink**) 09-30-2008, 01:21 AM

PM sent

qwak748 · #3 (**permalink**) 10-01-2008, 10:34 PM

whats up steve?

you slimmin down the garage?

stevet · #4 (**permalink**) 10-01-2008, 10:43 PM

Have to make room for the hypermotard and maybe a new superbike

G8RDuc · #5 (**permalink**) 10-02-2008, 04:45 PM

Where are you located in Florida?

stevet · #6 (**permalink**) 10-02-2008, 10:28 PM

I'm located in Jacksonville, Florida. My tech is Sebastian at Mellilimoto in Ocala. Are you in Gainesville?

G8RDuc · #7 (**permalink**) 10-02-2008, 11:01 PM

Quote:

Originally Posted by stevet

I'm located in Jacksonville, Florida. My tec is Sebastian at Mellilimoto in Ocala. Are you in Gainesville?

Yeah! Gainesville rocks and so does Sebastian. I know him well!

Talk to me about the heads you have. Are the Corse heads a better choice than the stock heads with SPS cams? Or vice versa?

stevet · #8 (**permalink**) 10-02-2008, 11:22 PM

Jimmy, what kind of bike do you have? the stock heads with sps cams and the bdc rocker are bulletproof for a street bike and make 6-10 more hp than stock when sebastian set them up. These would be a direct bolt on to a stock 996 and have already been degreed for stock motor with omega hc pistons. this set of heads only has two track days since set up. The Corsa heads are unobtainable and are absolutely fresh with just one dyno run. made 136hp on sebastians dyno but if you don't have hc pistons may not be much better than the stock heads. I really put them on the track bike for track use only. is yours a street or track bike?

G8RDuc · #9 (**permalink**) 10-03-2008, 12:52 AM

Quote:

Originally Posted by stevet

Jimmy, what kind of bike do you have? the stock heads with sps cams and the bdc rocker are bulletproof for a street bike and make 6-10 more hp than stock when sebastian set them up. These would be a direct bolt on to a stock 996 and have already been degreed for stock motor with omega hc pistons. this set of heads only has two track days since set up. The Corsa heads are unobtainable and are absolutely fresh with just one dyno run. made 136hp on sebastians dyno but if you don't have hc pistons may not be much better than the stock heads. I really put them on the track bike for track use only. is yours a street or track bike?

Definitely a street bike and my eventual goal is to have 130 at the rear. Right now, I'm 20 short of that. Where else would I find the additional 10-14 HP if I had your stock heads with SPS cams? I do have exhaust that is made for a better breathing motor (FBF 54mm Exhaust). The motor is stock besides the flywheel.

stevet · #10 (**permalink**) 10-03-2008, 02:09 AM

well, with a stock exhaust and these heads the 996 made 123hp. the 54 exhaust is the stuff so you already have that covered. sps cams, ported heads and h/c pistons should easily get you where you want to go. I have a set of heads at sebastians that are twomm over that would probably work for what you want to do. email me at steve@terbrueggen.com or call me at (904)655-8756 and we'll check with sebastian, but we could work something out swapping parts around if you want.

G8RDuc · #11 (**permalink**) 10-05-2008, 06:49 AM

Quote:

Originally Posted by stevet

well, with a stock exhaust and these heads the 996 made 123hp. the 54 exhaust is the stuff so you already have that covered. sps cams, ported heads and h/c pistons should easily get you where you want to go. I have a set of heads at sebastians that are twomm over that would probably work for what you want to do. email me at steve@terbrueggen.com or call me at (904)655-8756 and we'll check with sebastian, but we could work something out swapping parts around if you want.

Steve, did you get my email??

stevet · #12 (**permalink**) 10-05-2008, 01:30 PM

Hi Jimmy, shoot me another email. My box was full when I got home last night

Wow, used ducati parts seem to be in demand, I'll get back to you today if you get to me by this afternoon. thanks, steve

stevet · #13 (**permalink**) 10-08-2008, 03:12 AM

Yoyodyne clutch slave sold, front rotors sold! thanks, steve

stevet · #14 (**permalink**) 10-13-2008, 11:17 PM

998r bodywork sold, carbon heel guards sold, rotors sold, front end sold, thanks guys, appreciate the help, steve

stevet · #15 (**permalink**) 10-20-2008, 11:40 PM

sold 1 rear rotor also, still have another stock rear rotor, as well as two used titanium rear rotors, carbon battery trays (1new, 1used) and carbon chain guard, etc. thanks, steve

stevet · #16 (**permalink**) 10-22-2008, 10:36 PM

Hi Guys, I'll be out of town until next thursday, but leave me an email at steve@terbrueggen.com and I'll return it next friday. thanks, steve

stevet · #17 (**permalink**) 11-01-2008, 10:25 PM

still tons of parts left, let me know if you need motor, brakes, bodywork for 996, swingarm, shock etc. thanks, steve

Mr.Duc · #18 (**permalink**) 11-01-2008, 11:04 PM

Do you have an undertail oil breather box?

stevet · #19 (**permalink**) 11-08-2008, 11:57 AM

sold the oil breather box, but still have the airbox, ohlins rear shock, ohlins and stock steering damper, bottom half of engine, cases, covers, tranny, rear swingarm and corsa oil cooler. thanks, steve

pinky · #20 (**permalink**) 11-11-2008, 03:54 PM

Steve, got the air runners, very happy, thanks!

Cheers,

Armando